Spanco 300-050 Wall Mounted Jib Cranes offer a full cantilever design which transmits less direct force to the building column than tie-rod jib cranes. These industrial-duty overhead lifting devices can be used in a variety of applications to lift loads weighing up to 1000 lbs. Cranes feature 8’ to 30' long booms that can rotate up to 180°. Wall brackets support the boom eliminating the need for support under the beam and allowing a trolley to travel nearly the entire length of the boom. Jib cranes are engineered with a standard beam to eliminate off-center loading issues. The top and bottom wall brackets are made from steel tube welded to plating in an "I" configuration that provides maximum rigidity while providing ample length for solid connections between the brackets and the mast. To simplify installation, wall mounted jib cranes feature bolted mast to boom connections and bolt-on trolley stops. Beams are either S or W type with various flange widths depending on model. All swivel connections have bronze bushings and grease fittings to ease rotational friction, ensure a long service life, and decrease maintenance. Spanco 300-050 wall jib cranes meet AISC Steel Construction Manual, OSHA 1910.179, ANSI B30.11, AWS D1.1/D1.6, and CMAA Specification 74 Standards.
Spanco 300-050 Wall Mounted Jib Cranes are built to order with an estimated lead time to leave the warehouse of 10 to 12 business days.
Specifications:
- Complete system that includes wall brackets, beam/boom, and assembly hardware. Mounting hardware is NOT included
- 180° boom rotation
- Capacity: 1000 LBS
- Crane Structural Design Load = Crane’s Live Load Capacity + 15% for hoist and trolley weight + 25% for impact
- Beam lengths are 8' to 30' / Usable clear spans are 6' 5" to 27' 6-1/2"
- S or W Type beams with various sized flange widths - see specific models in chart below
- Full cantilever design transmits less direct force to building column than tie-rod supported cranes
- Swivel connections feature bronze bushings and grease fittings
- All steel construction
- 10 Year / 20,000 Hour Limited Non-Wearable Part Warranty (exclusions apply)
- Meets AISC Steel Construction Manual Part 5, OSHA 1910.179, ANSI B30.11, AWS D1.1/D1.6, and CMAA Specification 74 Standards
- See crane measurements on drawing in ADDITIONAL INFO above ↑
Options:
- Bumper Assemblies - includes 2 bumpers that attach to the beam - normally used at both ends of the beam to stop trolley from rolling off of the beam - See models in options chart below
- Tagline Assembly For Hoist Power Cord Management - includes welded tagline angles, tagline cable, (2) cable clamps, (2) eye bolts, pulley with cable ties every 5' - See models in options chart below
- Manual Rotational Stop - field welded in place to stop boom rotation at a specific desired position - See options chart below
- Multi-Position Boom Lock - allows the boom to be locked in place every 30°- See options chart below
- Festoon System - flat cable (4-Conductor #12) and box track for power to hoist - power only or power & control systems available - Contact HOF for a quote
- Motorized Boom Rotation With Controls - includes motor, reducer, & torque limiter (if applicable), & control panel. 460v motor is standard, 208/230v & 575v motors available - Contact HOF for a quote
- Presence Warning Devices - Warning Light and/or Crane Horn - may only be purchased for cranes with motorized rotation - Contact HOF for a quote
- Electrical Disconnects - may only be purchased for cranes with motorized rotation - Contact HOF for a quote
- Motor Brake - acts like a parking brake to reduce boom drift when motor is not in use - recommended for outdoor cranes - may only be purchased for cranes with motorized rotation - Contact HOF for a quote
- Special Finishes and/or Weatherization For Outdoor Use - Contact HOF for a quote
Hoist and Trolley sold separately. Click link to see our selection of Hoists and Trolleys
Crane should be inspected frequently to insure safe operation. Testing and inspection of the crane is the responsibility of the end user.
